Vinyl > Stucco > Weep Screeds

 

 

Foundation Weep Screed provides a straight and true screed surface at the base of stucco walls, while allowing excess moisture to escape the back of the stucco membrane. It is important for the water-resistant paper and metal lath to overlap the nailing flange of the weep screed. Check with local building codes for the proper clearance above grade. Building codes require this bead on framed walls. 10' standard length. Roof/Wall Screed uses the same design as the Foundation Weep Screed, except it is manufactured with a shorter (2-3/8") nailing flange. This design is ideal for roof-to-wall transitions found in both stucco and stone applications. Product No. Dimensions Ground Box
Product No.
Dimensions
Ground
Box Count
AMFWS-425-380
4 1/4"
3/8"
30
AMFWS-425-500*
4 1/4"
1/2"
30
AMFWS-425-580*
4 1/4"
5/8"
30
AMFWS-425-750*
4 1/4"
3/4"
30
AMFWS-425-780*
4 1/4"
7/8"
30


*Available in standard white, as well as tan, brown or gray (on exposed areas only).

 

 

Foundation Weep Screed

 

       
 

Roof/Wall Screed uses the same design as the Foundation Weep Screed, except it is manufactured with a shorter (2-3/8") nailing flange. This design is ideal for roof-to-wall transitions found in both stucco and stone applications.

Product No.
Nail Flange
Ground
Box Count
AMRWS-238-380
2 3/8"
3/8"
60
AMRWS-238-500
2 3/8"
1/2"
60
AMRWS-238-580
2 3/8"
5/8"
60
AMRWS-238-750
2 3/8"
3/4"
60
AMRWS-238-780
2 3/8"
7/8"
60

 

 
Roof / Wall Screed
       
 

Mid-Wall Weep Screed (Patent Pending) performs as an unpunched weep screed allowing excess moisture to escape the back of a stucco membrane. This screed also performs as an expansion (control) joint with twin grounds. It is installed where a framed stucco surface meets a masonry (concrete block) stucco surface. This condition is common between floors on 2-story homes and at the base of a gable receiving stucco.

The unpunched flange above must be installed extending at least one inch below the framing/ concrete joint. The weather barrier and lath should be installed over the solid upper flange to direct water to the foundation weep screed. The profile is manufactured with a 3½" nailing flange as required by code. 10' standard length.

Product No.
Ground A
Ground B
Box Count
AMMWS-780-500
7/8"
1/2"
15
AMMWS-780-580*
7/8"
5/8"
15


*Available in standard white, as well as tan, brown or gray (on exposed areas only).

 

Mid-Wall Weep Screed

 

       
 

Weep Screed Extended (Return) Leg is used like a regular foundation weep screed but covers the bottom edge of the sheathing in cases where the sheathing or framing extends beyond the edge of the foundation. This protects the edge of the sheathing from moisture and insect damage and closes the gap caused by the offset. 10' standard length.

NOTE: Weep screeds are required at the base of framed walls. This profile is manufactured with a 3½" vertical nailing flange as standard.

Product No.
Overall Height
Ground
Box Count
AMFWS-L-425-500
4 1/4"
1/2"
30
AMFWS-L-425-780
4 1/4"
7/8"
30

 

 

Weep Screed Extended (Return) Leg

       

xxxx Alabama Metal Industries. All Rights Reserved.